7 Day Internship on Automotive Dynamics & Designing

image-not-available
7 Day Internship on Automotive Dynamics & Designing

ABOUT THE COURSE

It is an intensive course in which we will you will learn about Static of Automobile Engineering, & Dynamic Balancing of subsystems of race vehicles. 

Course curriculum designed and guided by our reputed experts from Formula 1 and Automotive companies like Polaris, Ashok Leyland, Tata, Mahindra etc.

DAY WISE SCHEDULE

Day 1: Automobile Static Engineering

In this part we will be discussing static parts of automobile that how each and every component works:

  • Steering system - Hydraulic power steering, Electric steering, Worm & Sector, Four wheels turning
  • Engine working and fundamentals - Square engines, V cylinder engines, Power-Economy relations
  • Fundamentals of chassis design - Tub chassis (recently used by koenigsegg Agera R), Formula-1 chassis, sports & passenger car chassis, torsional rigidity of chassis
  • Suspension system - Double wishbone suspension, Solid Axle suspension, Hotchkiss suspensions, 2 Four-Link suspensions, De Dion suspensions, Air suspension, MacPherson suspension
  • Braking system - Hydraulic braking, Wedge braking, Power assistance braking, ABS with EBD
  • Types of subsystems: Chassis, Braking, Steering, Suspension and their disadvantages and advantages
Day 2 to 4: Automobile Dynamics

In this part we will be discussing dynamics of automobile in deep and discuss the following:

  • Linear roll generation, Diagonal load transfer, Lateral load transfer, Linear acceleration, Centrifugal acceleration
  • Linear de-acceleration, Roll center, Roll axis, Roll movement, Spring rate of tire, Self-aligning torque, Driveline torque
  • Engine electronics, Engine fuels, Various type of efficiencies
  • Super charging of engine, Types & Methods of super chargers
  • Engine emission control methods, Engine emission norms
  • How to balance all the components of a car
  • Steering dynamics for designing & balancing of a race and off-road vehicle
  • Braking performance parameters - balancing of brakes for a race and off-road vehicle
  • Suspension, Spring types and calculations, Dampers, Single tube dampers, Vehicle ride & handling, Roll gradient, Anti-roll bar stiffness, Damping curve, Critical damping roll center calculations for different type of suspensions, Wheel rate, Motion ratio, Frequency calculations
  • Transmission matching, Selecting the Engine Size and Final drive ratio for maximum speed 1st gear, 2nd, 3rd, 4th & 5th gear, Reverse gear calculation, Vehicle acceleration calculations, Van Doorne Continuously Variable Transmission (CVT), Torotrak Continuously Variable Transmission (CVT)
  • Derivation of turning equation - balancing of steering system for commercial and race vehicles (case study on balancing of race and off road vehicle)
  • CAD designing of vehicle chassis, Weldment structure, Part assembly, Engineering drawing sheets for part fabrication
  • Rendering tools, Chassis designing parameters - designing & balancing of space frame chassis of race car and ATV
Day 4 & 5: CAD Design Simulation

This will be the implementation of the things that we will learn in above two parts:

  • Introduction of 2-D sketching 3-D modeling
  • Ergonomics considerations in designing of a car
  • Tools & commands of designing, features – Weldments sketch, Evaluate, Office products,
  • Designing of Tires & Rims
  • Ride & handling consideration in design
  • Chassis designing and stress analysis of component
  • Decaling and rendering of a vehicle
  • Vehicle fabrication steps and technique
  • F.E.A – stress analysis on chassis design(space frame of an ATV), Front impact, Side impact and Roll over testing of frame
  • Thermal simulation of heating components
  • Parts assembly
  • Engineering drawing sheet generation from part file to fabrication
Day 6: Engine Part Modeling and Tuning

Engine performance & Design parameters, Engine emission norms, Engine fuels:

  • Piston CAD designing, Crankshaft cad designing, Intake manifold  designing, Exhaust manifold
  • Assembly of engine parts, Tuning parameters discussion, Mean effective pressure, Brake horse power, Fuel consumption, Valve timing, Ignition timings, Volumetric efficiency
  • Engine performance calculations, Effects of changing in intake absolute pressure, Relations between horsepower, cc, Torque, RPM, Various engine efficiencies (Mechanical, Volumetric, Thermal, Relative, Air-standard)
     
  • Engine Management Systems
  1. Sensor types
  2. Crankshaft speed position and Camshaft position
  3. Throttle position
  4. Air flow rate
  5. Inlet manifold absolute pressure
  6. Air and coolant temperature
  7. Air-Fuel ratio
  8. Knock
Day 7: Hands On Experience (Practical Session)

In this session participants will get hand on experience on different components of a vehicle:

  • Practical working of engine & transmission will be experienced by the participants while disassembling and assembling a multi cylinder IC engine
  • CRDI multi cylinder I.C Engine practical session (Hands on)
  • Commercial transmission practical (Hands on)
  • Assembly and disassembly by the participants
  • Parts working and design explanation
  • Introduction to “Engineering Design & Race Competitions”
  • Orientation session on “Scope of Automobile Sector”
  • Career guidance program
  • Quiz for certificate of appreciation & Internship opportunities

WHY TO JOIN

  • Learn from the best in the business including former Formula-1 Racing Marshalls.
  • Preparedness for race and design competitions organized by renowned automotive competitions such as BAJA, FORMULA-SAE, Go-Kart, Hybrid Vehicles, etc.
  • "Certificate of Participation” for all participants issued by “ELITE TECHNO GROUPS”, a team of Formula 1 Racing Marshalls, accredited by International organisation for Standardisation, United Kingdom (U.K).
  • Top 5 scorer will be rewarded with “Certificate of Appreciation” and will be provided Internship opportunitiesin top notch Automotive Companies.

Course Kit

Every Participant will get a DVD containing 32 e–books, dynamic calculations of different type of vehicles, videos tutorials of complex subsytems for further references. 

WHO ALL CAN ATTEND

  • The internship is designed for B.E/B.Tech - Automobile, Mechanical, Electronics, Electrical, Production and Industrial engineering students.
  • Diploma Engineers interested in pursuing further studies on part time or full time basis.
  • Automotive enthusiasts (under grad & passed out’s).  

Fees

Rs. 3990/- per participant including course kit and all taxes (no extra charges to participants for any activity during the training).

Upcoming workshops

What Student say about us

Aenean commodo ligal geate dolor. Aenan massa. Loren ipsum dolor sit amet,color
tetuer adiois elit, aliquam eget nibh etibra

This workshop work as a frontier for me to put up my theorotical knowledge into practical experience

Ahmad Arman
7 day STP on Go kart Design & Development, Chennai

I was amazed at the learning i received in this workshop

Vishnu Sharan
3 day training program on Automobile Vehicle Dynamics, Bengaluru

Thanks to ETG, that my horizons have broadened leaps & bounds

Rahul Malhotra
7 day training program on Automotive Dynamics & Designing,Ahmedabad

Attended my 3rd workshop with ETG, Actual Practical Knowledge

Shubham Kulkarni
13-07-201715 day STP on ATV Design and Development

These guys gave wings to my theoretical knowledge

Siddarth Verma
02-06-20175 days training program on Automotive Dynamics, Delhi